Top 10 common forklift crashes ， forklift operation must take note of these matters ！.

Don't undervalue the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the driver's sight, and the person in front could not be found, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the allowable width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur must first verify that the lots is steady and dependable.
4. The beginning should be slow-moving and steady.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are banned. High-speed doglegs will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to turn off the flame and slide, and it is prohibited to brake instantly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain security distance from the car in front. .
7. When the forklift is running, the tons needs to be in the lowest setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or packing. .
8. The height of the load must not block the driver's view. In unique conditions, when the thing impacts the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it needs to drive safely at a low rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is prohibited for workers to base on the fork to hold items and play a balancing function. .
12. If troubles are found, they will be repaired and reported in a timely way, and they will never operate with ailments or hide them.

filling and unloading.
1. When fork-loading items, the distance between the two forks need to be adjusted as needed to make the load of the two forks balanced and not skewed, and one side of the item should be against the rack. .
2. It is forbidden to work with a single fork or use a fork top or pull. In unique situations, security indication need to be set up to remind surrounding pedestrians. .
3. In the process of filling and dumping things, the forklift needs to be braked with the brake. .
4. The rate of the automobile must be sluggish and stable. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled items and harm individuals. .
5. When making use of a fork to fork the goods, the fork must be as deep as possible under the lots, and it must be noted that the fork pointer must not touch various other items or objects. The lots ought to be maintained with very little back tilt of the gantry so that the lots does not slide in reverse. The mast can be slanted forward somewhat when the load is decreased to enable easy positioning of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with tough objects with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding prevent the collapse of the goods and injure people. .
8. Overwhelming is banned, and it is restricted to make use of forks to lift workers to take part in high-altitude operations to avoid high-altitude dropping crashes. .
9. It is not allowed to use the brake inertia to slip, place, round or roll things. .
10. It is not allowed to use forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork frame.
2. Pull the parking brake manage to dead or depress the hand brake switch.
3. The engine is shut off and the power is cut off. (Except for special scenarios, such as the vehicle driver does not leave the lorry's line of sight and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Stand-on Electric Pallet Stacker Precautions.
1. Prior to Stand-on Electric Pallet Stacker and after the forklift operation, the appearance ought to be inspected, and fuel, lubricating oil and air conditioning water must be added.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are normal.
5. After the forklift is running, the exterior leak ought to also be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect prior to leaving the car;.
2. When you run into someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m in the air;.
5. The transforming ought to not be too sharp to avoid the propensity of " complimentary switching";.
6. Running up and down the incline should be sluggish and consistent, and no switching on the incline is allowed.
7. Do not drive across the slope. When the slope is greater than 10%, the automobile should be driven backwards when worsening;.
8. When the forklift employees bring the goods and move on, if they encounter large or hefty items and go to the chauffeur's line of sight, they must take the turning around workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Solitary fork procedure is not permitted.
2. It is not allowed to lift the goods for long distance driving.
3. It is not enabled to get the goods by passing on the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not permitted to use inertia pressure to pick up the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll items.
7. It is not enabled to bring individuals to service the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, narrow roads, train crossings;.
2. Sections with a longitudinal slope greater than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the section with the very same size as the challenge should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844